MYRI10GE(4D) Devices MYRI10GE(4D)
myri10ge - Myricom Myri10GE 10Gb PCI Express NIC Driver
/dev/myri10ge*
The myri10ge Gigabit Ethernet driver is a multi-threaded, loadable,
clonable, GLD-based STREAMS driver that supports the Data Link
Provider Interface, dlpi(4P), on Myricom Myri10GE 10-Gigabit Ethernet
controllers.
The myri10ge driver functions include controller initialization,
frame transmit and receive, promiscuous and multicast support,
multiple transmit and receive queues, support for TCP Large Send
Offload, support for TCP Large Receive Offload, and error recovery
and reporting.
The cloning character-special device, /dev/myri10ge, is used to
access all Myricom Myri10GE 10 -Gigabit Ethernet dev ices installed
within the system.
The myri10ge driver is managed by the dladm(8) command line utility.
dladm allows VLANs to be defined on top of myri10ge instances and for
myri10ge instances to be aggregated. See dladm(8) for more details.
You must send an explicit DL_ATTACH_REQ message to associate the
opened stream with a particular device (PPA). The PPA ID is
interpreted as an unsigned integer data type and indicates the
corresponding device instance (unit) number. The driver returns an
error (DL_ERROR_ACK) if the PPA field value does not correspond to a
valid device instance number for the system. The device is
initialized on first attach and de-initialized (stopped) at last
detach.
The values returned by the driver in the DL_INFO_ACK primitive in
response to your DL_INFO_REQ are:
o Maximum SDU is 9000.
o Minimum SDU is 0.
o DLSAP address length is 8.
o MAC type is DL_ETHER.
o SAP (Service Access Point) length value is -2, meaning the
physical address component is followed immediately by a
2-byte SAP component within the DLSAP address.
o Broadcast address value is the Ethernet/IEEE broad- cast
address (FF:FF:FF:FF:FF:FF).
o Once in the DL_ATTACHED state, you must send a DL_BIND_REQ
to associate a particular SAP with the stream.
Link speed and mode can only be 10000 Mbps full-duplex. See the IEEE
802.3 Standard for more information.
/dev/myri10ge*
Special character device.
/kernel/drv/myri10ge
32-bit device driver (x86)
/kernel/drv/amd64/myri10ge
64-bit device driver (x86)
/kernel/drv/sparcv9/myri10ge
64-bit device driver (SPARC)
/kernel/drv/myri10ge.conf
Configuration file
See attributes(7) for a description of the following attributes:
+--------------------+-----------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+--------------------+-----------------+
|Architecture | SPARC, x86 |
+--------------------+-----------------+
|Interface Stability | Committed |
+--------------------+-----------------+
streamio(4I), dlpi(4P), driver.conf(5), attributes(7), dladm(8),
netstat(8)
Writing Device Drivers
Network Interface Guide
STREAMS Programming Guide
IEEE 802.3 Standard
September 10, 2009 MYRI10GE(4D)
NAME
myri10ge - Myricom Myri10GE 10Gb PCI Express NIC Driver
SYNOPSIS
/dev/myri10ge*
DESCRIPTION
The myri10ge Gigabit Ethernet driver is a multi-threaded, loadable,
clonable, GLD-based STREAMS driver that supports the Data Link
Provider Interface, dlpi(4P), on Myricom Myri10GE 10-Gigabit Ethernet
controllers.
The myri10ge driver functions include controller initialization,
frame transmit and receive, promiscuous and multicast support,
multiple transmit and receive queues, support for TCP Large Send
Offload, support for TCP Large Receive Offload, and error recovery
and reporting.
Application Programming Interface
The cloning character-special device, /dev/myri10ge, is used to
access all Myricom Myri10GE 10 -Gigabit Ethernet dev ices installed
within the system.
The myri10ge driver is managed by the dladm(8) command line utility.
dladm allows VLANs to be defined on top of myri10ge instances and for
myri10ge instances to be aggregated. See dladm(8) for more details.
You must send an explicit DL_ATTACH_REQ message to associate the
opened stream with a particular device (PPA). The PPA ID is
interpreted as an unsigned integer data type and indicates the
corresponding device instance (unit) number. The driver returns an
error (DL_ERROR_ACK) if the PPA field value does not correspond to a
valid device instance number for the system. The device is
initialized on first attach and de-initialized (stopped) at last
detach.
The values returned by the driver in the DL_INFO_ACK primitive in
response to your DL_INFO_REQ are:
o Maximum SDU is 9000.
o Minimum SDU is 0.
o DLSAP address length is 8.
o MAC type is DL_ETHER.
o SAP (Service Access Point) length value is -2, meaning the
physical address component is followed immediately by a
2-byte SAP component within the DLSAP address.
o Broadcast address value is the Ethernet/IEEE broad- cast
address (FF:FF:FF:FF:FF:FF).
o Once in the DL_ATTACHED state, you must send a DL_BIND_REQ
to associate a particular SAP with the stream.
Configuration
Link speed and mode can only be 10000 Mbps full-duplex. See the IEEE
802.3 Standard for more information.
FILES
/dev/myri10ge*
Special character device.
/kernel/drv/myri10ge
32-bit device driver (x86)
/kernel/drv/amd64/myri10ge
64-bit device driver (x86)
/kernel/drv/sparcv9/myri10ge
64-bit device driver (SPARC)
/kernel/drv/myri10ge.conf
Configuration file
ATTRIBUTES
See attributes(7) for a description of the following attributes:
+--------------------+-----------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+--------------------+-----------------+
|Architecture | SPARC, x86 |
+--------------------+-----------------+
|Interface Stability | Committed |
+--------------------+-----------------+
SEE ALSO
streamio(4I), dlpi(4P), driver.conf(5), attributes(7), dladm(8),
netstat(8)
Writing Device Drivers
Network Interface Guide
STREAMS Programming Guide
IEEE 802.3 Standard
September 10, 2009 MYRI10GE(4D)